Laser Standards

Laser Safety falls under the ANSI 136.1 standard in the United States and the EN207/EN208/EC60825 standard in Europe.

Lasers are categorized by the ANSI Z136.1 standard into the following general categories. NOTE: Category alone is not sufficient to determine if or which eye protection is required.

Class Definition Pulse Length
1 Non-hazardous Eyewear not required.
1M Eye safe visible laser (400-700nm) if used without magnifying optics. Eyewear not required unless used with magnifying optics.
2 Eye safe visible laser (400-700nm) (safe within the blink reflex of 0.25s). Eyewear not required.
2M Eye safe visible laser (400-700nm) (safe within the blink reflex of 0.25s) if used without magnifying optics. Eyewear recommended.
3R Likely unsafe for intrabeam viewing. Maximum Permissible Exposure (MPE) is up to 5 times class 2 limit for visible lasers of 5 times class 1 limit for invisible lasers. Eye hazard; eyewear is recommended.
3B Eye hazardous for intrabeam viewing. Limited diffuse hazard. Eye hazard; eyewear is recommended.
4 Eye and skin hazard for direct and diffuse exposure. Fire and burn hazard. Eye protection and other personal safety equipment is required.


ANSI Z136.1 requires specification of laser safety eyewear according to optical densities (OD), and allows a Nominal Hazard Zone (NHZ) to be calculated, outside which diffuse viewing eyewear is allowed.

Optical Density (OD) is a measure of the attenuation of energy passing through a filter. The higher the OD value, the higher the attenuation and the greater the protection level. In other words, OD is a measure of the laser energy that will pass through a filter.
OD is the logarithmic reciprocal of transmittance, expressed by the following: D? = -log10 T ?, where T is transmittance.

OD (Optical Density) Transmission in % Attenuation Factor
0 100% 1
1 10% 10
2 1% 100
3 0.1% 1,000
4 0.01% 10,000
5 0.001% 100,000
6 0.0001% 1,000,000
7 0.00001% 10,000,000


European Laser Safety Standards EN207/208/60825

European laser safety regulations EN 207/EN208 consider Optical Density and also the power/energy density (power over time over area) of the laser when determining laser safety requirements. Like ANSI Z136.1, laser safety eyewear must provide sufficient optical density to reduce the power of a laser to be equal or less than the Maximum Permissible Exposure levels (MPE), but it must also provide damage threshold protection (direct hit over a given amount of time/energy). Under EN207, Laser safety goggles must protect against direct intrabeam exposure to the laser.

The EN207 standard requires that eyewear is labeled to with protection levels that detail their damage thresholds, (e.g. 10600 D L5 (where L5 reflects a power density of 100 MegaWatt/m2 during a 10 seconds direct hit test at 10,600nm).

EN207 L- ratings account for the damage threshold of the eyewear material, i.e., the power density eyewear will withstand, and requires actual laser stability testing for at least 10 seconds (cw) or 100 pulses (pulsed modes).

 

 


Modes of Operation

Lasers operating at different modes have different power density characteristics and often different eyewear requirements.

Mode Definition Pulse Length
D Continuous Wave (cw) with consistent average power greater than 0.25 second
I Pulsed: short single or periodic energy emission > 1 µs to 0.25 s
R Giant Pulsed: very short single or periodic energy emission 1 µs to 1 ns
M Mode Locked < 1 ns (pico and femtosecond)

 


A Comprehensive Resource Booklet for Laser Safety

About the Author
Ken Barat is the former Laser Safety Officer for Lawrence Berkeley Nat Lab and the National Ignition Facility Directorate. Presently, he is providing laser safety consulting under the title of Laser Safety Solutions. He is the author of four texts on laser safety as well as numerous articles and presentations worldwide. He is an OSA distinguished speaker, Fellow of the Laser Institute of America, and a senior member in IEEE and SPIE. He was the chair and organizer of the first seven LSO workshops. ANSI committee member and chair.


NoIR Laser
NoIR provides industry-defining protection and visibility for the world of laser applications. Made in the USA and CE-Certified, LaserShield® filters deliver performance and protection with an eye on comfort. With more than 125 filters and a frame to fit any face, LaserShields are the point where Form and Function converge. All LaserShield® filters are produced in Southeast Michigan, where NoIR is committed to excellence in product quality and customer service.